On this page
Calculator
Enter the length and width of the rectangle that contains the roof as seen from above. For an L-shaped or cut-up house, run each rectangle separately and add the results.
Roof squares calculator
Enter the roof's footprint (the area the roof covers seen from above, including overhangs), its pitch, and a waste allowance. Everything runs in your browser; nothing is sent anywhere.
Formula: footprint × √(1 + (rise ÷ 12)²) = sloped roof area; ÷ 100 = squares; × (1 + waste) = squares to order. A roofer's measurement (tape, drone or satellite report) replaces this number on the quote.
What a roofing square is
Roofers buy, price and quote in squares. A square is 100 sq ft of roof surface, which is about three bundles of a typical architectural shingle. It is a measure of the sloped surface, not the house's floor area, so two houses with the same living space can have very different square counts.
Three things drive the count: the footprint (including eaves and rake overhangs, usually 12–24 inches on Front Range homes), the pitch, and how cut-up the roof is. A simple gable on a ranch house is close to footprint × pitch factor. A two-story with hips, valleys and dormers adds both area and waste.
Pitch factors
Pitch is written as rise over 12 inches of run, for example 6:12. The factor converts flat footprint to sloped area. The table is computed from the formula, not looked up.
| Pitch | Angle | Area factor | 1,000 sq ft footprint becomes |
|---|---|---|---|
| 2:12 | 9.5° | 1.014 | 1,014 sq ft |
| 3:12 | 14.0° | 1.031 | 1,031 sq ft |
| 4:12 | 18.4° | 1.054 | 1,054 sq ft |
| 5:12 | 22.6° | 1.083 | 1,083 sq ft |
| 6:12 | 26.6° | 1.118 | 1,118 sq ft |
| 7:12 | 30.3° | 1.158 | 1,158 sq ft |
| 8:12 | 33.7° | 1.202 | 1,202 sq ft |
| 9:12 | 36.9° | 1.250 | 1,250 sq ft |
| 10:12 | 39.8° | 1.302 | 1,302 sq ft |
| 12:12 | 45.0° | 1.414 | 1,414 sq ft |
| 14:12 | 49.4° | 1.537 | 1,537 sq ft |
| 16:12 | 53.1° | 1.667 | 1,667 sq ft |
Below 3:12, most shingle makers do not allow shingles at all, and Denver's 2015 roofing guideline required modified rolled roofing or an EPDM-type membrane under 1:12. Low-slope roofs are covered on the flat-roofing page.
How to measure your footprint without climbing
- Walk the eavesMeasure each wall at ground level with a tape or a measuring wheel.
- Add the overhangAdd the eave overhang on each side (measure one from the ground to the fascia line).
- Split the shapeBreak an L or T into rectangles; garages and porches with their own roof count too.
- Run each pieceRun each rectangle through the calculator with its own pitch and add them.
County assessor records list living area, not roof area, so they are a starting point only. Satellite and drone measurement reports used by roofers measure the sloped planes directly and should be close to your total plus waste.
Finding your pitch from the ground or the attic
- In the attic: hold a level horizontally against a rafter, mark 12 inches along it, and measure straight up from that mark to the rafter's underside. That measurement in inches is the rise.
- At a gable end: measure the run (half the gable width) and the height from the top plate to the ridge; rise per 12 = height ÷ run × 12.
- From a photo: a phone angle app on a straight-on photo of the gable gives an angle; match it to the angle column above.
Choosing a waste allowance
Waste covers shingles cut at hips, valleys and rakes, starter strip and ridge caps. Our choices in the calculator are a convention, not a rule from any code or source:
| Roof shape | Allowance in the tool |
|---|---|
| Simple gable, few penetrations | 10% |
| Hip roof, a few valleys or dormers | 15% |
| Cut-up roof: many hips, valleys, dormers | 20% |
Ask each roofer what waste figure they used. A quote that prices waste separately is easier to compare than one that buries it in the square count.
A worked Denver example
A 1960s Denver ranch with a 40 × 38 ft footprint after overhangs (1,520 sq ft) and a 5:12 gable roof:
- Pitch factor for 5:12 = √(1 + (5/12)²) = 1.083.
- Sloped area = 1,520 × 1.083 = 1,647 sq ft = 16.5 squares.
- With 10% waste = 18.1 squares to order.
A two-story with the same 1,520 sq ft footprint has the same roof, even though its floor area is twice as large. That is why "price per square foot of house" figures mislead on roofing.
Using the number on a quote
Bring your square count to every quote and ask the roofer to write theirs on the contract. Colorado's roofing statute, C.R.S. 6-22-103, already requires the contract to state the scope of work and materials; the square count is the clearest way to state the scope. If the counts differ by more than the waste allowance, ask for the measurement report.
For a hail claim, the adjuster's estimate also lists squares. Comparing the adjuster's count with your own catches missed slopes before the claim closes. See who pays what on a hail roof.
Common questions
How many squares is a 2,000 sq ft house?
It depends on the footprint and pitch, not the floor area. A 2,000 sq ft two-story house might sit on a 1,000 sq ft footprint plus overhangs; at 6:12 that is about 12–13 squares before waste. The same floor area on one story is roughly twice the roof.
What is the pitch factor for a 6/12 roof?
About 1.118. Multiply the footprint by 1.118 to get the sloped roof area. The factor is the square root of 1 + (rise ÷ 12)².
Why is my roofer's square count higher than this calculator?
Roofers add waste for hips, valleys, starter and ridge caps, and they measure every plane, dormer and overhang. A count 10–20% above the measured area is normal; one far above that deserves a question and a copy of the measurement report.
Can I calculate a roof pitch from this page?
Yes. Pitch is the rise in inches over 12 inches of run. Hold a level 12 inches long against a rafter or the roof surface and measure the vertical gap at its end; the table below converts it to a factor and an angle.