On this page
What counts as low slope
Roof pitch is written as rise over a 12-inch run. A 4:12 roof rises 4 inches every foot; a "flat" roof usually still falls ¼ inch or so per foot to drain. Two thresholds matter in Denver's documents:
Sources: City and County of Denver, Residential Roofing Guidelines (rev. 28 Aug 2015) (verify); City and County of Denver, CPD — Green Buildings Ordinance Rules and Regulations (effective 9 Oct 2023), Table 1. Read 2026-10-20.
Between those lines, shingle makers set their own minimums, often with extra underlayment. If your porch, addition or garage sits near 2:12, ask the roofer which slope they measured and which product rules apply at that number.
TPO, EPDM and modified bitumen
Three membrane families dominate low-slope residential work in the metro. Core Roofing Systems prices TPO and EPDM separately on its Denver cost page, and Denver's guideline names modified rolled roofing and EPDM-type systems.
| System | What it is | Seams | Questions for the roofer |
|---|---|---|---|
| TPO | Thermoplastic single-ply sheet, usually white or light colored | Heat-welded | Sheet thickness; mechanically fastened or adhered; insulation board under it |
| EPDM | Synthetic rubber single-ply sheet, traditionally black | Taped or glued | Thickness; seam tape system; how flashings at walls and curbs are made |
| Modified bitumen | Asphalt-based rolled roofing with polymer modifiers, often with a granule cap sheet | Torched, cold-applied or self-adhered laps | Number of plies; application method (torch work on an occupied house); cap-sheet surface |
Color matters on bigger buildings: Denver's Green Buildings Ordinance sets a minimum solar reflectance for low-slope roofs on buildings of 25,000 sq ft or more (covered on the commercial roofing page). On a house it is a comfort and energy choice, not a legal one.
Denver rules for membrane roofs
The material rule
Denver's Residential Roofing Guidelines (revised 28 August 2015) state that slopes below 1:12 on one- and two-family dwellings need modified rolled roofing or an EPDM-type system. The guideline predates Denver's 2025 code, so treat it as the last published statement and confirm details with Community Planning and Development.
The certificate
Denver lists a Specialty Class D certificate called Roof Covering/Waterproofing – Commercial & Residential. Its scope is "installation of commercial and residential roof coverings, including valleys, gutters, downspouts and waterproofing," under the on-site supervision of a certificate holder. Applicants document 24 projects from 24 different months, and at least 75% of those must be different types of low-slope systems on commercial buildings. The separate Roofing-Shingles – Residential Only certificate is aimed at residential roofing systems.
Source: City and County of Denver, CPD — Specialty Class D certificates (Roof Covering/Waterproofing – Commercial & Residential), read 2026-10-20.
Permits for repairs
Repair thresholds differ by city: Denver's guideline at more than 10% of the roof, Centennial and Lakewood at 100 sq ft, Littleton at 1 square in aggregate over 365 days. Full replacement needs a permit everywhere we checked. See roof permits in the Denver metro.
Ponding, drains and snow
Low-slope roofs fail differently from shingle roofs. Watch for:
- Ponding: water still standing a day or two after rain or melt shows the roof is not draining as designed. It stresses seams and adds weight.
- Blocked drains and scuppers: leaves and grit from spring hail storms collect at drains. Clear them before winter.
- Sitting snow: snow does not shed from a flat roof. Denver's 2025 Residential Code raised the ground snow load from 35 to 43 psf. That is a structural number, not a shingle one, but it is why the deck, its fastening and its drainage get checked on a tear-off.
- Flashings: most leaks start where the membrane meets a wall, curb, skylight or vent, not in the open field.
Snow load source: City and County of Denver, Community Planning and Development, "Snow Load Changes: 2025 DBC, 2024 IBC/IRC, ASCE 7-22", read 2026-09-23.
Hail can still puncture or bruise a membrane, especially over soft insulation. After a storm, ask for close-up photos of the membrane surface near drains and seams, not just the shingled slopes.
Published Denver prices
Two Denver roofing companies publish whole-job figures for low-slope systems. We show them as printed; they are not our prices, and they assume jobs the companies consider typical.
Show the data as a table
| Source and system | Low | High |
|---|---|---|
| Elk: flat / low-slope | $8,000 | $16,000 |
| Core: TPO | $13,000 | $24,000 |
| Core: EPDM | $14,000 | $26,000 |
Sources: Elk Roofing (Denver), dated 2026-01-21; Core Roofing Systems (Denver metro), dated 2026. Read 2026-09-23. Elk prints its top as "$16,000+".
No Denver source we found publishes a per-square price for low-slope membranes, so we do not show one. The flat roof replacement cost page explains what moves a membrane quote up or down.
Repair or replace?
- Find the leakMost are at flashings, seams or drains. A localized fault is a repair.
- Check the insulationWet insulation under the membrane spreads the problem; ask for core cuts or moisture readings.
- Count the layersDenver allows two roof layers at most, so a second overlay may not be possible.
- Compare the thresholdA repair that crosses your city's permit line needs a permit like a reroof.
Repairs to a membrane need compatible materials: a TPO patch welds only to clean TPO, and EPDM needs its own primers and tapes. Ask the roofer to name the membrane they found and the patch system they will use.
What a flat-roof quote should list
Use this list on every bid. If a line is missing or a term is unclear, write to us with the question and we will point you to the rule or source behind it.
- Membrane type, thickness and attachment (fastened, adhered or ballasted), with the manufacturer.
- Tear-off scope, insulation type and thickness, and any tapered insulation to fix ponding.
- Drains, scuppers and flashing details at every wall, curb and penetration.
- For Denver jobs, which Class D certificate the supervisor holds.
- Permit, inspections and the written-contract terms under C.R.S. 6-22-103.
Common questions
What roofing does Denver require on a nearly flat roof?
Denver's 2015 Residential Roofing Guidelines require modified rolled roofing or an EPDM-type system on slopes below 1:12 for one- and two-family dwellings. Shingles are not an option there. The guideline is old, so confirm current detail with Community Planning and Development.
Who can install a membrane roof in Denver?
Denver's Roof Covering/Waterproofing – Commercial & Residential certificate covers "commercial and residential roof coverings, including valleys, gutters, downspouts and waterproofing", and its applicants must show that at least 75% of their documented projects were low-slope systems on commercial buildings. Ask which certificate the supervisor holds.
How much does a flat roof cost in Denver?
Core Roofing Systems publishes $13,000–$24,000 for TPO and $14,000–$26,000 for EPDM on low-slope roofs, and Elk Roofing prints $8,000–$16,000+ for flat and low-slope systems. Those are published third-party ranges for typical jobs, not quotes.
Do I need a permit to repair a flat roof?
Usually only above a size threshold that each city sets: over 10% of the roof in Denver's guideline, 100 sq ft in Centennial and Lakewood, and 1 square in aggregate in Littleton. A full replacement always needs one.