Skip to content

Metal roofing

Metal roofing in Denver: what to check before you switch

A metal roof in the Denver metro is usually standing seam or stone-coated steel, and Denver licenses its installers under a separate "Metal Roof Installer" certificate. Published Denver prices run about $700 to $2,300 per square, two to three times architectural shingles. The case for it here is hail and longevity; the checks are your HOA covenants, whether the product's impact rating covers dents, and whether your insurer prices the roof any differently.

Prices are published by named Denver roofing companies (dated 2026, read 2026-09-23); certificate scope from Denver CPD, read 2026-10-20.

An independent publisher, not a roofing contractor. Facts last checked . How we source.

On this page
  1. Standing seam vs stone-coated steel
  2. Metal and Denver hail
  3. Denver licenses metal roofers separately
  4. Published Denver prices
  5. Snow, slope and fire
  6. HOAs and metal roofs
  7. What a metal roof quote should list
  8. Common questions

Standing seam vs stone-coated steel

"Metal roof" covers two very different products on Front Range houses, and Denver price sheets list them separately.

Two common residential metal systems
SystemWhat it isWhat to ask
Standing seamLong vertical panels joined at raised seams, fastened with concealed clips. Smooth painted steel or aluminum.Panel gauge, seam height, clip type, and whether the finish carries a separate paint warranty.
Stone-coated steelPressed steel panels coated with stone granules, shaped to look like shake, tile or shingle.The product's UL 2218 class, any hail warranty and its limits, and the batten or deck system it needs.

Both are usually installed over a full deck with underlayment. Neither is a do-it-once-and-forget product: fasteners, flashings and penetrations still need inspection after big storms.

Metal and Denver hail

The Denver metro logged 869 hail reports in 2016–2025 across seven counties, 28 of them at 2.5 inches or larger. That size matters for metal, because it is the limit some stone-coated steel makers write into their hail warranties.

DECRA, for example, states that its stone-coated steel profiles "hold the highest Class 4 impact rating from Underwriters Laboratories" and that its roofs are "backed by a warranty against hailstones up to 2.5 inches in diameter." Read the warranty itself before relying on that: a warranty against penetration is not a warranty against dents.

Sources: DECRA Metal Roofing, home page (stone-coated steel), read 2026-10-20; our NOAA hail count. Named as an example of how such warranties are worded, not a recommendation.

Dents are the catchUL 2218 rates impact resistance by dropping steel balls twice on the same spot: Class 1 is a 1.25-inch ball from 12 ft, Class 2 1.5 in from 15 ft, Class 3 1.75 in from 17 ft, Class 4 a 2-inch ball from 20 ft. To pass, the covering must not crack or split. The pass mark is cracking, not denting. A dented standing-seam roof can be fully watertight and still look damaged, and many homeowner policies treat that as cosmetic. Ask your insurer how it handles cosmetic damage to metal before you choose a smooth-panel finish.

Denver licenses metal roofers separately

Colorado has no state roofing license, so cities set the rules. Denver's Community Planning and Development lists distinct Specialty Class D supervisor certificates for roofing, including:

  • Metal Roof Installer: "Installation of metal roofs only," under the on-site supervision of a Class D Metal Roof Installer certificate holder; two years of field experience, no test.
  • Roofing-Shingles – Residential Only: residential roofing systems, 24 projects from 24 different months of experience.
  • Roof Covering/Waterproofing – Commercial & Residential: broader roof coverings including waterproofing, with most documented experience on low-slope commercial systems.

Source: City and County of Denver, CPD — Specialty Class D certificates (Metal Roof Installer; Roofing-Shingles – Residential Only), read 2026-10-20.

For a Denver address, ask which certificate the job's supervisor holds and confirm it covers metal. In suburbs, the city's own register applies; see roofing licenses in the Denver metro. Lakewood's 2026 handout, for example, requires a Lakewood contractor registration of 5h or higher for any hired roofer.

Published Denver prices

Four Denver roofing companies publish metal prices; one cost publisher prints a statewide figure. They do not agree, partly because "metal" spans painted panels to stone-coated profiles. The bars share one scale in dollars per square (100 sq ft of roof).

Published installed metal roof price per square, Denver metro (2026)
Published installed metal roof price per square, Denver metro (2026) Road Home Exteriors: $700 to $1,100; Gates Roofing (metal): $800 to $1,500; Core: stone-coated steel: $1,275 to $2,300 $0$620$1,240$1,860$2,480 Road Home Exteriors $700–$1,100 Gates Roofing (metal) $800–$1,500 Core: stone-coated steel $1,275–$2,300
Show the data as a table
SourceLowHigh
Road Home Exteriors$700$1,100
Gates Roofing (metal)$800$1,500
Core: stone-coated steel$1,275$2,300

Sources: Road Home Exteriors (Denver metro and Front Range) (2026); Gates Roofing (Denver) (dated 2026-02-02); Core Roofing Systems (Denver metro) (2026). Read 2026-09-23. Gates prints its top as "$1,500+".

  • Whole-roof: Elk Roofing (Denver) prints metal at $18,000–$30,000+ installed for a single-family Denver home (dated 2026-01-21).
  • Statewide: This Old House, roof replacement cost in Colorado prints metal at $9.43 per square foot and an average of $14,763 for Colorado as a whole (updated 2026-06-12). Statewide averages. Its own per-square-foot rate times its example roof areas does not reproduce its totals, so we show its figures as printed and do not derive from them.

Against architectural asphalt at $650–$730 a square at Core and $450–$600 at Gates, metal is roughly double to triple. More detail, including how to compare two metal quotes, is on the metal roof cost page. These are published third-party ranges, not our prices.

Snow, slope and fire

Three Front Range conditions shape a metal roof design:

  • Snow load. Denver's 2025 Residential Code raised the ground snow load from 35 to 43 psf. That is a structural number, not a shingle one, but it is why the deck, its fastening and its drainage get checked on a tear-off. Snow slides off smooth metal more readily than off shingles, so ask where it will land (walkways, decks, gas meters) and whether snow guards are part of the bid.
  • Low slopes. Denver's 2015 roofing guideline requires modified rolled roofing or an EPDM-type membrane on slopes under 1:12. Panel systems have their own minimum slopes in the manufacturer's instructions; ask for the number in writing for your pitch.
  • Fire rating. Lakewood requires every roof covering to be Class A fire rated. DECRA, for one, lists its stone-coated steel systems as Class A. Ask for the fire listing of the exact product and underlayment being installed.

Sources: Denver CPD snow load changes (read 2026-09-23); City and County of Denver, Residential Roofing Guidelines (rev. 28 Aug 2015) (verify, 2015); City of Lakewood, Roofing and Re-roofing handout (2026 edition), read 2026-10-20.

HOAs and metal roofs

Many Front Range subdivisions have architectural covenants that list approved roof materials and colors. A Colorado HOA may not require roofing material that is flammable, and since HB24-1091 may not prohibit fire-hardened building materials. The statute has no comparable protection for hail-resistant or metal roofing as such; covenants on color and profile still apply.

Source: C.R.S. 38-33.3-106.5; Colorado Division of Real Estate HOA Center advisory on HB24-1091, read 2026-10-20.

Whether a particular steel roof is a "fire-hardened building material" under the statute depends on whether it meets one of the standards the law names (ignition-resistant construction under the International Wildland-Urban Interface Code, the NFPA wildland standards, or IBHS's wildfire-prepared home requirements). If you are relying on that argument, get the product's documentation to the HOA with your application. The HOA roofing rules guide walks through the approval process.

What a metal roof quote should list

Check each line against the bid in hand. Questions on permits, hail ratings and insurance that apply to every roof type are answered on our Denver roofing FAQ.

  • Exact product, profile, gauge or thickness, and finish, with the manufacturer's name.
  • Impact rating (UL 2218 class) and fire rating as listed for the assembly being installed.
  • Underlayment, ice barrier (required in Centennial and Littleton), flashing details and snow guards.
  • Tear-off and deck repair pricing, and who pulls the permit under which city license or certificate.
  • Manufacturer warranty terms (including any hail limit) and the roofer's workmanship warranty, separately.
  • The written-contract terms Colorado requires under C.R.S. 6-22-103.

Common questions

How much does a metal roof cost in Denver?

Denver contractors publish $700–$1,500+ per square for metal (Road Home Exteriors and Gates Roofing) and up to $2,300 per square for stone-coated steel (Core Roofing Systems). Elk Roofing prints $18,000–$30,000+ for a whole metal roof. These are published third-party ranges, not quotes.

Does Denver require a special license for metal roofing?

Denver issues a separate Specialty Class D certificate for "Metal Roof Installer", covering installation of metal roofs only, alongside the residential shingle certificate. Ask which certificate the supervisor on your job holds and check it with Community Planning and Development.

Will hail dent a metal roof?

It can. Impact ratings test for cracking and penetration, not dents. Some stone-coated steel products carry a UL Class 4 rating and a manufacturer warranty against penetration by hail up to 2.5 inches, but a cosmetic dent may not be covered by either the warranty or your insurance policy.

Can my HOA ban a metal roof in Colorado?

Colorado law stops an HOA from requiring flammable roofing such as cedar shakes and, since HB24-1091, from prohibiting fire-hardened building materials. It does not create a general right to metal roofing, so covenants on material, color and profile can still apply. Read your design guidelines and apply before you sign.

Get roofing quotes in the Denver metro

Free and no obligation. Tell us the job and ZIP; we check whether a partner roofer covers it before passing anything on.

Enter a Denver-metro ZIP (800–804). Outside that, we do not have a partner yet.
Please add your name.
A phone number is how the roofer reaches you.
Please add a working email.
Please add the street address for the job.
Get roofing quotes