Skip to content

Flat roof cost

Flat roof replacement cost in Denver

A flat or low-slope roof replacement in Denver runs $8,000 to $26,000 on the ranges local roofers published in 2026: $8,000–$16,000+ for flat systems at Elk Roofing, and $13,000–$24,000 for TPO and $14,000–$26,000 for EPDM at Core Roofing Systems. Size, insulation, drains and the number of old layers decide where your roof lands.

Two named Denver sources, each dated. Published third-party figures, not quotes from us.

An independent publisher, not a roofing contractor. Facts last checked . How we source.

On this page
  1. Published totals
  2. TPO, EPDM and modified bitumen
  3. Denver rules for low slopes
  4. Slope, ponding and snow
  5. Repair, recover or replace
  6. What moves a flat-roof price
  7. What no source publishes
  8. What the quote should say
  9. Common questions

Published totals

Published installed totals for flat and low-slope roofs in Denver, 2026 (USD)
Published installed totals for flat and low-slope roofs in Denver, 2026 (USD) Flat and low-slope systems (Elk): $8,000 to $16,000; TPO (Core): $13,000 to $24,000; EPDM (Core): $14,000 to $26,000 $0$7,020$14,040$21,060$28,080 Flat and low-slope systems (E… $8,000–$16,000 TPO (Core) $13,000–$24,000 EPDM (Core) $14,000–$26,000
Show the data as a table
System and sourceLowHigh
Flat and low-slope systems (Elk)$8,000$16,000
TPO (Core)$13,000$24,000
EPDM (Core)$14,000$26,000

Elk Roofing (dated 2026-01-21, "$8,000–$16,000+"); Core Roofing Systems (dated 2026). Read 2026-09-23.

Elk's lower band is described as "flat and low-slope systems" on single-family homes, and its upper end is open ("+"). Core's TPO and EPDM figures are its own low-slope work. Neither publishes a per-square price for membranes, so we do not convert these to squares.

Sources: Elk Roofing (Denver); Core Roofing Systems (Denver metro).

TPO, EPDM and modified bitumen

Low-slope systems you will see on Denver quotes
SystemWhat it isPublished Denver figure
TPOSingle-ply thermoplastic sheet, usually white, with heat-welded seams.$13,000–$24,000 (Core)
EPDMSingle-ply synthetic rubber, usually black, with taped or glued seams.$14,000–$26,000 (Core)
Modified bitumenAsphalt-based rolled roofing in layers, torched, mopped or self-adhered.no published figure

Denver's guideline names modified rolled roofing and EPDM-type systems as the acceptable coverings below 1:12, so all three appear on metro quotes for bungalows, mid-century homes, porches and garages.

Denver rules for low slopes

Shingle wind rating by street centerline: 90 mph at Federal Blvd, 100 mph at Sheridan Blvd, 110 mph at Kipling St (ASTM D7158 or D3161). Slopes under 1:12 need modified rolled roofing or an EPDM-type membrane.

The same guideline sets the permit trigger at more than 10% of the roof area and allows two layers at most. The newest residential roofing guideline Denver publishes is dated 2015. Treat the wind-zone figures as historical until CPD confirms them under the 2025 Denver Building Code.

Source: City and County of Denver, Residential Roofing Guidelines (rev. 28 Aug 2015), read 2026-10-20 (verify).

Suburbs differLittleton, Centennial, Lakewood and Thornton each publish their own reroof rules. Lakewood requires a Class A fire-rated covering on every roof. Compare them on roof permits by city.

Slope, ponding and snow

A "flat" roof is never meant to be dead flat. The International Residential Code, which Denver and its suburbs adopt with local amendments, sets a minimum design slope of 1/4 inch per foot (1/4:12) for built-up, modified bitumen, EPDM and TPO coverings. A roof framed flatter than that needs tapered insulation or cricketing to reach it, and that board is often the line that separates a low quote from a high one.

Denver adds a weight problem. The city's 2025 code raised the ground snow load from 35 to 43 pounds per square foot. Snow does not slide off a low-slope roof the way it leaves a 6:12 shingle roof; it sits there, melts in the afternoon sun and refreezes overnight. Water that stands for more than a couple of days after a thaw is ponding, and ponding is what rots decking and opens seams.

  • Ask the roofer to mark low spots and existing drain locations on a sketch before pricing.
  • If water ponds now, ask whether the quote includes tapered insulation, added drains or a cricket behind any parapet or chimney, or whether it simply replaces the membrane on the same plane.
  • On a tear-off, ask what happens if the deck under the ponding area is soft. A per-sheet price in writing stops that becoming an open-ended change order.

Sources: International Code Council, 2021 IRC sections R905.9 to R905.13 (minimum slopes by covering), codes.iccsafe.org; Denver CPD, 2025 snow-load changes. Read 2026-10-26.

Repair, recover or replace

Three different jobs get called "a new flat roof", and they are priced differently.

The three kinds of flat-roof job
JobWhat it meansDenver limits
RepairPatching seams, flashings or a damaged area.Past 10% of the roof area, Denver's guideline treats it as a reroof that needs a permit.
RecoverA new membrane over the existing one, usually with a cover board.Two layers at most. If one recover is already on, the next job is a tear-off.
ReplaceStrip to the deck, repair it, insulate, and install a new system.Permit required. The point at which drainage and insulation can actually be fixed.

A recover can be sensible on a dry, sound roof with one layer. It is a poor buy over wet insulation, because the water stays trapped under the new sheet. Ask the roofer how they checked for wet insulation (a core cut, or a moisture survey) and to say so in the quote.

What moves a flat-roof price

  • Area: the main driver, as with every roof.
  • Layers to remove: old built-up or rolled roofs are heavy to strip and dispose of.
  • Insulation: rigid insulation board under the membrane, and tapered board to create drainage slope, add material and labor.
  • Drains and edges: scuppers, internal drains, gutters and edge metal are where low-slope roofs leak.
  • Deck repairs: ponding water rots decking; ask for a per-sheet replacement price in writing.
  • Penetrations: skylights, vents and rooftop equipment each need flashing details.

None of these has a published Denver price we could read, so each should appear as a line or an allowance on your quote.

What no source publishes

We found no published Denver figure for: modified bitumen roofs, flat-roof repairs, per-square membrane pricing, or tapered insulation. We do not fill those gaps with national averages. If you need a number, three itemized local quotes are the only reliable source.

What a flat-roof quote should say

  • Membrane type, thickness and maker, and how seams are joined.
  • How many existing layers come off, and disposal.
  • Insulation type and thickness, and whether tapered board corrects ponding.
  • Every drain, scupper and edge detail.
  • The permit, the city license number, and the warranty terms in writing.

On a residential flat roof over $1,000, Colorado's C.R.S. 6-22 requires a signed written contract before work begins. More on the systems themselves: flat and low-slope roofing.

Common questions about this cost

How much does a flat roof replacement cost in Denver?

Elk Roofing publishes $8,000–$16,000+ for flat and low-slope systems on a Denver home. Core Roofing Systems publishes $13,000–$24,000 for TPO and $14,000–$26,000 for EPDM. Published 2026 figures, not our quotes.

Is TPO or EPDM cheaper in Denver?

In the one source that prices both, Core Roofing Systems, the bands overlap almost entirely: TPO $13,000–$24,000 and EPDM $14,000–$26,000. Roof size, insulation and drains matter more than the membrane.

Can I use shingles on a low-slope roof in Denver?

Not on the flattest roofs. Denver's 2015 residential roofing guideline requires modified rolled roofing or an EPDM-type membrane on slopes under 1:12. Shingle makers also set their own minimum slopes.

Can a new membrane go over my old flat roof?

Sometimes. Denver's 2015 guideline allows two roof layers at most, so a recover is possible only over a single existing layer, and it should not go over wet insulation. Ask how the roofer checked for moisture.

Who can install a flat roof in Denver?

A contractor licensed by the city where the house is. Denver licenses roofing contractors through Community Planning and Development; confirm the license covers membrane roofing before you sign. See licensing.

Get roofing quotes in the Denver metro

Free and no obligation. Tell us the job and ZIP; we check whether a partner roofer covers it before passing anything on.

Enter a Denver-metro ZIP (800–804). Outside that, we do not have a partner yet.
Please add your name.
A phone number is how the roofer reaches you.
Please add a working email.
Please add the street address for the job.
Get roofing quotes