Skip to content

Roof installation, Denver metro

Roof installation in Denver: what a correct install includes, layer by layer

A correct Denver-metro roof installation is a permitted assembly, not just shingles: sound deck, underlayment, drip edge, flashing, ventilation and a covering fastened to the maker's high-wind pattern, inspected by the city. What differs by address is mostly the ice barrier: Centennial and Littleton require it at the eaves, while Lakewood, Thornton and Denver's 2015 guideline do not.

Rules from each city's own roofing document, read 2026-10-20. We are a publisher, not a roofer.

An independent publisher, not a roofing contractor. Facts last checked . How we source.

On this page
  1. Installation vs replacement
  2. The layers of a correct install
  3. Ice barrier: depends on the city
  4. Drip edge, nails and deck
  5. Wind and impact ratings
  6. Fire rating
  7. Low-slope sections
  8. What gets inspected
  9. Reading an installation quote
  10. Common questions

Installation vs replacement

"Roof installation" covers two jobs. One is a roof on a structure that has never had one: a new house, an addition, a detached garage, an accessory dwelling unit. The other is the installation phase of a replacement, after the old roof comes off. The specification below applies to both. The tear-off, permit triggers and insurance side of replacing an existing roof are on roof replacement in Denver.

The legal frame differs. Colorado's residential roofing statute, C.R.S. 6-22, excludes new construction, so a roof on a new house is governed by your builder's contract, not by the roofing contract rules. A re-roof or an addition to an existing house is generally covered when the contract exceeds $1,000.

Source: C.R.S. 6-22-102, Definitions, read 2026-10-20.

The layers of a correct install

Read from the deck up, a steep-slope asphalt roof is a stack. Each layer has a job, and a quote should name each one.

Cross-section of a steep-slope asphalt roof at the eave From bottom: roof deck, ice barrier at the eave where the city requires it, synthetic or felt underlayment, drip edge at the edge, starter course, then field shingles fastened with six nails, and ridge vent at the top. Roof deck (sheathing) Ice barrier at eave (Centennial, Littleton) Underlayment Drip edge Shingles: starter course, then field, 6 nails each Ridge vent
Simplified eave-to-ridge section. Ice barrier is shown where a city requires it; elsewhere it depends on the shingle maker's instructions.
  1. Deck. Solid sheathing fastened to code. Littleton requires a minimum 3/8 in panel overlay where spaced-board gaps exceed 1/2 in, with a sheathing-nailing inspection.
  2. Ice barrier at the eaves, where required (next section).
  3. Underlayment over the rest of the deck. Thornton's mid-roof inspection expects 75–100% of underlayment installed.
  4. Drip edge at the eaves (Littleton) and at eaves and rakes (Lakewood asphalt reroofs, Thornton).
  5. Flashing at valleys, walls, chimneys and penetrations.
  6. Starter course and shingles, fastened to the maker's pattern.
  7. Ventilation: intake and exhaust balanced, vents reconnected.

Sources: City of Littleton, Policy #20-005, Roof Covering and Installation Requirements (5/14/2020, 3rd rev. 6/12/2023); City of Thornton Building Inspection Division, Roofing Standards (last update 9-12-25); City of Lakewood, Roofing and Re-roofing handout (2026 edition). Read 2026-10-20.

Ice barrier: it depends on the city

Ice barrier is a self-adhering membrane at the eaves that seals around nails and stops meltwater from an ice dam getting under the shingles. Metro cities disagree on whether it is required:

Ice barrier requirement by city (read 2026-10-20)
CityRule
DenverNot required at eaves (2015 guideline)
LittletonRequired: ASTM D1970 ice barrier at least 2 ft inside the exterior wall line at the eaves of all conditioned structures
CentennialRequired on all roofs
LakewoodNot required (metal drip edge required at eaves; asphalt reroofs need it at eaves and rakes)
ThorntonNot required unless the shingle manufacturer's instructions specify it
Code minimum is not the whole answerWhere the city does not require it, the shingle maker may still require ice barrier for the warranty, which is why Thornton's standard defers to the manufacturer's instructions. North-facing eaves that hold snow are where it earns its cost. See ice dams.

Drip edge, nails and deck

Three details separate a careful install from a fast one, and two cities write them into their rules:

  • Six nails per shingle. Littleton's Policy 20-005 sets six nails per asphalt shingle as the minimum, and Thornton's mid-roof photo set must show the six-nail pattern.
  • Drip edge. Lakewood requires it at all eaves, and at eaves and rakes on asphalt shingle roofs; Thornton requires it at eaves and rakes, extending over the sheathing at the fascia; Littleton requires galvanized drip edge.
  • Approved shingles. Thornton keeps a list of accepted shingle lines; anything not listed needs a national wind warranty of at least 80 mph sustained or 90 mph three-second gust and prior approval.

Denver's 2025 code raised the residential ground snow load from 35 to 43 psf. That is a structural number rather than a shingle one, but it is why the deck and its fastening get checked whenever the roof is open.

Sources: Littleton Policy #20-005; Thornton Roofing Standards; City and County of Denver, Community Planning and Development, "Snow Load Changes: 2025 DBC, 2024 IBC/IRC, ASCE 7-22".

Wind and impact ratings

Two wind tests appear on shingle wrappers. ASTM D3161 (fan-induced) Class A, D and F correspond to 60, 90 and 110 mph. ASTM D7158 (uplift) Class D, G and H correspond to 90, 120 and 150 mph basic wind speed on the older ASCE 7-05 basis (about 115, 150 and 190 mph ultimate under ASCE 7-10). Denver's 2015 guideline sets the minimum rating by street centerline, from 90 mph at Federal Boulevard to 110 mph at Kipling Street; confirm the current figure with the city.

Shingle wind classes on the wrapper
TestClassRated speed
ASTM D3161A / D / F60 / 90 / 110 mph
ASTM D7158 (ASCE 7-05 basis)D / G / H90 / 120 / 150 mph

UL 2218 rates impact resistance by dropping steel balls twice on the same spot: Class 1 is a 1.25-inch ball from 12 ft, Class 2 1.5 in from 15 ft, Class 3 1.75 in from 17 ft, Class 4 a 2-inch ball from 20 ft. To pass, the covering must not crack or split. Our Class 4 guide covers whether it is worth it here.

Sources: Professional Roofing (NRCA), wind resistance classifications for asphalt shingles; GAF, Timberline AS II product page (UL 2218 test summary). Read 2026-10-20.

Fire rating

Lakewood's 2026 handout requires all roof coverings to be Class A fire rated. Boulder County requires Class A roofs in its wildfire zones. If you are choosing wood shakes or a specialty product anywhere along the foothills, confirm the fire class before you order. Colorado HOA law also bars an association from requiring flammable roofing.

Source: City of Lakewood, Roofing and Re-roofing handout (2026 edition), read 2026-10-20.

Low-slope sections

Shingles need slope to shed water. Denver's guideline requires modified rolled roofing or an EPDM-type membrane on slopes under 1:12 for one- and two-family homes. Porch roofs, additions and garages often fall in this range, so a quote for a whole house may need two systems. See flat and low-slope roofing.

What gets inspected

  1. SheathingWhere new decking or an overlay goes on (Littleton, Thornton).
  2. Mid-roofUnderlayment and flashing in, part of the covering on (Littleton, Centennial, Thornton).
  3. PhotosLakewood inspects by uploaded photos; Thornton by texted photos.
  4. FinalIn person or by video call (Thornton since 28 Aug 2025).

The permits guide has each city's inspection rules side by side.

Reading an installation quote

A good quote names the products, not just "shingles". Check that it lists:

  • Shingle maker, line, wind class and impact class
  • Underlayment type and ice barrier (with how far up from the eave)
  • Drip edge at eaves and rakes, and new flashing
  • Nailing pattern (six nails)
  • Ventilation plan and vent replacements
  • Permit, inspections and who attends them

To check the area the quote is based on, use the roof squares calculator, then compare the price with the published bands in the cost guide.

Common questions

What is the difference between roof installation and roof replacement?

Installation is a roof on a new structure or bare deck: a new home, an addition, a garage or an ADU. Replacement removes an existing roof first. Colorado's roofing contract law (C.R.S. 6-22) excludes new construction, so a new-build roof is covered by your general building contract rather than that statute.

Is ice and water shield required in Denver?

Not by Denver's 2015 roofing guideline, Lakewood or Thornton (Thornton defers to the shingle maker). Centennial requires an ice barrier on all roofs, and Littleton requires an ASTM D1970 ice barrier at least 2 ft inside the wall line at the eaves of conditioned buildings.

How many nails per shingle are required?

Littleton's Policy 20-005 requires at least six nails per asphalt shingle, and Thornton's photo inspection checks for a six-nail pattern. Shingle makers' high-wind instructions also call for six. Ask for the nailing pattern in the contract.

Does a new roof need a Class A fire rating?

Lakewood requires all roof coverings to be Class A fire rated under its 2026 handout. Most asphalt shingles are Class A, but some wood and specialty products are not, so confirm the rating if you choose anything unusual.

Who checks that a roof was installed correctly?

The city building inspector, through the permit. Depending on the city that means a mid-roof inspection, photo inspections or a video final. Ask for the photos the roofer submits.

Get roof installation quotes

Free and no obligation. Tell us the job and ZIP; we check whether a partner roofer covers it before passing anything on.

Enter a Denver-metro ZIP (800–804). Outside that, we do not have a partner yet.
Please add your name.
A phone number is how the roofer reaches you.
Please add a working email.
Please add the street address for the job.
Get roofing quotes