Skip to content

Metal roof cost

Metal roof cost in Denver

Expect $700–$2,300 per square installed for a metal roof in Denver, going by what local roofers published in 2026, and Elk Roofing puts a typical single-family metal roof at $18,000–$30,000 or more. Stone-coated steel sits at the top of that band ($1,275–$2,300 per square at Core Roofing). Metal starts roughly where architectural asphalt ends.

Published figures from four named Denver-metro sources and one statewide publisher, each dated. Not quotes from us.

An independent publisher, not a roofing contractor. Facts last checked . How we source.

On this page
  1. Price per square
  2. Whole-roof totals
  3. Metal against asphalt
  4. Which metal is being quoted
  5. Denver factors that change the price
  6. Minimum slopes and low sections
  7. Reading a metal quote line by line
  8. What no source publishes
  9. Common questions

Price per square

Published installed $ per square for metal roofing in Denver, 2026, with asphalt for scale
Published installed $ per square for metal roofing in Denver, 2026, with asphalt for scale Metal (Road Home): $700 to $1,100; Metal (Gates): $800 to $1,500; Stone-coated steel (Core): $1,275 to $2,300; Architectural asphalt, for scale: $400 to $730 $0$620$1,240$1,860$2,480 Metal (Road Home) $700–$1,100 Metal (Gates) $800–$1,500 Stone-coated steel (Core) $1,275–$2,300 Architectural asphalt, for sc… $400–$730
Show the data as a table
Material and sourceLowHigh
Metal (Road Home)$700$1,100
Metal (Gates)$800$1,500
Stone-coated steel (Core)$1,275$2,300
Architectural asphalt, for scale$400$730

Road Home Exteriors (2026), Gates Roofing (2026-02-02, prints "$800–$1,500+"), Core Roofing Systems (2026); asphalt band from the same sources. Read 2026-09-23.

The spread is wide because "metal" covers several products. Road Home Exteriors' and Gates Roofing's figures are for metal roofing generally; Core Roofing's is specifically stone-coated steel. None of the sources we read prints a separate standing-seam price per square.

Whole-roof totals

Published whole-roof figures for metal in Denver and Colorado
SourceScopePublished figure
Elk Roofing
dated 2026-01-21
Denver single-family, installed$18,000–$30,000+
This Old House
updated 2026-06-12
Colorado statewide average$14,763 avg ($9.43/sq ft)

The two do not describe the same roof. Elk's is a Denver contractor's range for a full home; This Old House's is a statewide average. Statewide averages. Its own per-square-foot rate times its example roof areas does not reproduce its totals, so we show its figures as printed and do not derive from them.

Metal against asphalt

On the same 25-square roof, the published bands give about $10,000–$18,250 for architectural asphalt and $17,500–$57,500 for metal, before adders. That is multiplication of published bands, not a quote, but it shows the scale: the low end of metal overlaps the top of asphalt, and stone-coated steel can cost two to three times a standard shingle roof.

Hail and insuranceSome metal and stone-coated steel products carry a UL 2218 Class 4 rating; others do not, and dents on metal can be treated as cosmetic under some policies. Ask your insurer how it treats cosmetic damage to metal before you choose. Colorado law does not require a credit for impact-resistant roofs.

Which metal is being quoted

  • Standing seam: long vertical panels with concealed fasteners, common on modern homes and low-slope sections.
  • Stone-coated steel: steel pressed into shingle, shake or tile shapes with a granule coating; Core Roofing's $1,275–$2,300 per square.
  • Exposed-fastener panels: ribbed panels screwed through the face, mostly on outbuildings and garages.

Ask each quote to name the product, panel gauge, finish, and whether snow retention is included. Without those, two "metal roof" quotes are not comparable.

Denver factors that change the price

  • Snow retention: Front Range snow slides off metal in sheets. Snow guards over doors, walks and lower roofs are a design item, not an extra to skip.
  • Fire rating: Lakewood requires every roof covering to be Class A fire rated, per its 2026 handout. Confirm the assembly's rating, not just the panel's.
  • HOA approval: A Colorado HOA may not require roofing material that is flammable, and since HB24-1091 may not prohibit fire-hardened building materials. The statute has no comparable protection for hail-resistant or metal roofing as such; covenants on color and profile still apply.
  • Tear-off: Denver's 2015 guideline allows two roof layers at most; check whether the quote overlays or strips.

Sources: City of Lakewood, Roofing and Re-roofing handout (2026 edition); C.R.S. 38-33.3-106.5; Colorado Division of Real Estate HOA Center advisory on HB24-1091. Read 2026-10-20.

Minimum slopes and low sections

Not every metal product suits every part of a roof. The International Residential Code, adopted with local amendments across the metro, allows standing-seam panels down to 1/4:12, but lapped panels without sealant need at least 3:12, and metal shingles also need 3:12. On a Denver house with a low porch roof or a shed dormer, a "metal roof" quote may quietly switch those sections to a membrane. That is fine, but it should say so.

Snow matters here too. Denver's 2025 code raised the design ground snow load to 43 psf. Metal sheds snow fast, which is good for the structure and bad for whatever is below the eave: a gutter, a deck, a parked car or a person at the front door. Snow guards are priced per piece or per run, and no Denver source we read publishes that price, so ask for it as its own line.

Sources: International Code Council, 2021 IRC R905.4 and R905.10, codes.iccsafe.org; Denver CPD, 2025 snow-load changes. Read 2026-10-26.

Reading a metal quote line by line

Metal quotes vary more than shingle quotes because the product choices are wider. Before comparing totals, line up these items.

What to find on each metal roof bid
LineWhy it matters in Denver
Product and profileStanding seam, stone-coated steel and exposed-fastener panels sit in different price bands, per the sources above.
Gauge and finishThinner steel dents more easily in hail. Ask for the gauge in writing and the paint system's warranty terms.
Impact ratingIf you want a Class 4 premium discount, the product needs a UL 2218 Class 4 listing, and your insurer decides what credit, if any, applies.
UnderlaymentHigh-temperature underlayment is common under metal. Ask which one, and whether ice barrier runs up from the eaves.
Snow retentionWhere guards go and how many. It is a safety item over doors and walks.
Tear-offOverlay is limited by Denver's two-layer cap. Know whether the old roof comes off.
Permit and licenseThe roofer's license must come from the city the house is in. Check it on the city register.

Then ask each roofer the same question: how many squares is this price built on? The roof squares calculator gives you a rough count to test the answer against.

What no source publishes

No Denver source we read publishes: a standing-seam-only price per square, a metal repair price, a lifetime cost comparison with asphalt, or a typical insurance credit for metal. Where we have no published figure, we say so rather than estimate. More on the material itself is on metal roofing in Denver.

Common questions about this cost

How much does a metal roof cost in Denver?

Elk Roofing publishes $18,000–$30,000+ for a metal roof on a single-family Denver home. Per square, published bands run $700–$2,300 installed, from about $700 at the low end of Road Home Exteriors' range to $2,300 at the top of Core Roofing's stone-coated steel range.

Is metal cheaper than asphalt over the life of the roof?

No Denver source we read publishes a lifetime-cost comparison, so we do not offer one. The upfront difference is clear: published metal bands start where architectural asphalt bands end.

Can my HOA stop me installing a metal roof?

Colorado law stops an HOA from requiring flammable roofing and, since HB24-1091, from banning fire-hardened materials, but it has no specific protection for metal as such. Read your covenants and get approval first. See HOA roofing rules.

Is stone-coated steel the same as standing seam?

No. Stone-coated steel is pressed into shingle, shake or tile profiles and coated with granules; standing seam is long panels joined by raised seams. Core Roofing's $1,275–$2,300 per square figure is for stone-coated steel.

Get roofing quotes in the Denver metro

Free and no obligation. Tell us the job and ZIP; we check whether a partner roofer covers it before passing anything on.

Enter a Denver-metro ZIP (800–804). Outside that, we do not have a partner yet.
Please add your name.
A phone number is how the roofer reaches you.
Please add a working email.
Please add the street address for the job.
Get roofing quotes